Search by property

This page provides a simple browsing interface for finding entities described by a property and a named value. Other available search interfaces include the page property search, and the ask query builder.

List of results

• Model:HAMSOM  + (Default: 3D Temperature and salinity field 3D Velocities 2D Sea Surface Height)
• Model:The TELEMAC system  + (Depend on different modules that are using … Depend on different modules that are using, it can produce hydrodynamics, such as water velocity and depth; vertical density (3D); temperature plumes and salt wedge; water quality; sediment concentration and transport; underground water velocity field; wave parameters;und water velocity field; wave parameters;)
• Model:Gvg3Dp  + (Depending on the flags indicated in the in … Depending on the flags indicated in the input file, typical flow quantities are stored to the file at the given time steps.<br></br>Velocities, Pressure, Concentration (of the particles).<br></br>Depending on the problems, some other quantities could be stored too.e problems, some other quantities could be stored too.)
• Model:TURBINS  + (Depending on the flags set in the "input.i … Depending on the flags set in the "input.inp" file, flow properties such as velocity, pressure, particle concentration(s), particle deposit mass, bottom shear stress, kinetic and potential energy, dissipation rate, suspended particle mass, current front location, and etc are recorded at the given timesteps.d etc are recorded at the given timesteps.)
• Model:GeoClaw  + (Depth, momentum on adaptive grid at specified output times. Time series at specified gauge locations. Maxima observed over full simulation on specified grid.)
• Model:HBV  + (Discharge)
• Model:FuzzyReef  + (Dynamic variables: # water energy # depositional (seafloor) slope Final output: # carbonate productivity rate # depositional facies)
• Model:BRaKE  + (Elevation and slope arrays as well as optional information about bed cover and shear stress distributions, as well as block size distributions and incision rate records.)
• Model:Kirwan marsh model  + (Elevation, Biomass, Accretion Rate, Erosion Rate, and other characteristics of every cell in domain. Also outputs spatially averaged statistics.)
• Model:GOLEM  + (Elevation, drainage area, and related gridded information.)

• Model:LOADEST  + (Estimated constituent loads)

• Model:SBEACH  + (Estimated post-storm beach profile, cross-shore profile of: maximum wave height; maximum water elevation plus setup; volume change)
• Model:Detrital Thermochron  + (Estimates of the erosional history and spatial patterns and model diagnostic plots.)
• Model:Rescal-snow  + (Evolving 3D cellspace and 2D elevation map)
• Model:SICOPOLIS  + (Extent and thickness of the ice sheet, Velocity field, Temperature field, Water content field (temperate regions), Age of the ice, Isostatic displacement and temperature of the lithosphere.)
• Model:BarrierBMFT  + (Extent, and elevation, and cross-shore boundary locations of barrier, marsh (back-barrier and mainland), bay, and forest ecosystems; organic and mineral deposition; shoreline locations; dune elevations; overwash & shoreface fluxes)
• Model:Non Local Means Filtering  + (Filtered DEM: A new, filtered DEM in *.flt binary format. Noise: A *.flt binary format grid of the filtered noise.)
• Model:GSSHA  + (Flow rates, depths, soil moisture, sediment fluxes, erosion/deposition, contaminant/nutrient fluxes and concentrations, groundwater levels, reservoir storages.)
• Model:LOGDIST  + (Flow velocities at N levels in the vertical, assuming a logarithmic velocity profile)
• Model:WASH123D  + (Fluid velocity, pressure, temperature, sal … Fluid velocity, pressure, temperature, salinity, concentrations, thermal flexes, and matrial fluxes at all nodes at any desired time. volumetric, energy, and mass balance at all types of boundaries and the entire boundary at any specified time. Br>For details refer to Yeh et al., 2005 Technical Report on WASH123DYeh et al., 2005 Technical Report on WASH123D)
• Model:RivMAP  + (For a single image: centerlines, widths, c … For a single image: centerlines, widths, channel direction, curvatures</br>For multiple images: (centerline) migration areas, erosion and accretion areas, cutoffs, cutoff statistics, channel belt boundaries, grid generation to map spatial changes, spacetime maps of changes in planform variablestime maps of changes in planform variables)