Search by property

This page provides a simple browsing interface for finding entities described by a property and a named value. Other available search interfaces include the page property search, and the ask query builder.

List of results

• Model:NEXRAD-extract  + (Angular resolution around the radar; gridded data typically have km-nmi-size pixels)
• Model:TauDEM  + (Applies to any resolution topographic grid, though is most sensible for grids with resolution from 2 to 50 m.)
• Model:REF-DIF  + (Assumptions: The REF/DIF 1 model, in parab … Assumptions:</br>The REF/DIF 1 model, in parabolic form, has a number of assumptions inherent in it and it is necessary to discuss these directly. These assumptions are: </br># Mild bottom slope.</br># Weak nonlinearity.</br># The wave direction is confined to a sector ±70 ◦ to the principal assumed wave direction, due to the use of the minimax wide angle parabolic approximation of Kirby (1986b). parabolic approximation of Kirby (1986b).)
• Model:GLUDM  + (At the moment the resolution of the input controls the resolution of the output. This is a global model but can be applied to smaller domains.)
• Model:WBMsed  + (Available datasets are for global and continental domains. Realistic high-res simulations for global scale is 6 arc-min and for continental 3 arc-min. Higher resolution datasets are available for both (e.g. 15 arc-sec for Europe).)
• Model:GEOMBEST++  + (Cell length - 10 - 100 meters Cell height - 0.01 - 0.5 meters)
• Model:GEOMBEST++Seagrass  + (Cell length: 10 - 100 m (typically 50 m) Cell height 0.01 - 0.5 m (typically (0.1 m))
• Model:CarboLOT  + (Cells are approximately 1-1000m in scale; map areas 10-100km on side.)
• Model:Barrier Inlet Environment (BRIE) Model  + (Coastal barrier ~10-100 km length scales, and ~100 m alongshore resolution. Parameterizations not suitable for small-scale (tidal inlet etc) analyses)
• Model:RASCAL  + (Code has been most commonly run for 10x5 m … Code has been most commonly run for 10x5 m cells (with the long axis parallel to flow) and domain size of 1.27 x 1.86 km. Other scales are possible, but adding additional cells will slow down processing. This model is only designed to simulate mean flows; resolution of fine turbulence structure is not possible with the code.e structure is not possible with the code.)

• Model:Area-Slope Equation Calculator  + (Computer memory.)

• Model:GEOMBEST-Plus  + (Constraints: * Cell length - 10 - 100 meters * Cell height - 0.01 - 0.5 meters)
• Model:BarrierBMFT  + (Cross-shore transect length can extend 10's of km from the ocean barrier shoreface into the mainland. Grid resolution on the barrier is 10 m, and 1 m spacing from the back-barrier marsh to the mainland.)
• Model:CAM-CARMA  + (Currently there are only initial data sets for 10x15 degrees longitude and latitude. This model is meant for global scale dynamics.)
• Model:WACCM-EE  + (Currently, 4x5 degree, with 66 vertical levels up to 140 km. Resolution can be increased if neccessary)
• Model:Avulsion  + (Delta-scale)
• Model:GSSHA  + (Dependent upon computational power and memory.)
• Model:Landlab  + (Depends on application/process)
• Model:ParFlow  + (Depends upon application.)
• Model:PyDeltaRCM  + (Domain should be 10s of Kms in x and y. Cell spacing should be 10s of meters.)
• Model:FineSed3D  + (Domain should be large enough to resolve the bottom boundary layer, meanwhile, the grid resolution should be fine enough to resolve all the essential turbulence scales.)