Model help:Subside: Difference between revisions
mNo edit summary |
m (WikiSysop moved page Model help:Subside to Temp:Subside without leaving a redirect) |
(No difference)
|
Revision as of 09:58, 22 July 2015
Subside
The Subside is a 1D and 2D flexure model, and a part of the Sedflux model.
Model introduction
The model is used to simulate the lithospheric load changes as the model evolves. Depending upon how the load distribution develops, this flexure can result in the basin uplifting or subsiding (or both). The pattern of subsidence in time and space largely determines the gross geometry of time-bounded units because it controls the rate at which space is created for sedimentation.
Model parameters
Uses ports
This will be something that the CSDMS facility will add
Provides ports
This will be something that the CSDMS facility will add
Main equations
- Deflection of Earth's crust
[math]\displaystyle{ w \left (\lambda r \right ) = {\frac{q \lambda}{2 \pi \rho_{d}g}} Kei \left (\lambda r \right ) }[/math] (1)
- Flexural parameter
[math]\displaystyle{ \lambda = \left ({\frac{D}{\rho_{d}g}}\right )^ \left ({\frac{-1}{4}}\right ) }[/math] (2)
- Time delay between the addition of load and the lithosphere's response
[math]\displaystyle{ w \left (t \right ) = w_{0} \left ( 1 - exp \left (- t / t_{0} \right ) \right ) }[/math] (3)
Symbol | Description | Unit |
---|---|---|
w | deflection of earth's crust | - |
λ | flexural parameter | - |
r | distance from the point load | L |
q | point load | - |
Kei | Kelvin function | - |
ρd | density of the asthenosphere | M / L3 |
g | acceleration due to gravity | L / T2 |
d | flexural rigidity of the earth's crust | - |
w0 | equilibrium deflection | - |
t | time since the load was applied | T |
t0 | response time associated with mantle viscosity | T |
D | grain size (usually in mm or μm) | L |
Notes
- Equation 1 predicts the deflection due to a point load; it does not account for the additional weight of material that fills the deflection. For instance, a rise in sea level will cause a deflection that will be filled with additional water, which in turn will cause further deflection. If we know the density of material that fills the deflection, the total deflection is increased by a factor of (( ρd )/(ρd - ρw ))1.25 (Angevine et al., 1990). Using ρd = 3300 kg / m3, and ρw 1030 kg / m3, this amounts to an increase in deflection by a factor of 1.6. Unfortunately, in general, we do not know the density of the added (or removed) material as it could be either air or water. Thus, we solve for the total deflection by iteratively solving equation 1 and updating the load after successive iterations until the solution converges.
- Because the viscous asthenosphere has to flow out of the way before the lithosphere can deflect, there will be a time delay between the addition of load and the lithosphere’s response. equation (3) expresses this time delay as an exponential (Peltier, 1998).In reality, response time is a function of the viscosity of the underlying mantle (Peltier, 1998) Typical relaxation times vary from about 1500 to 5000 years (Peltier, 1998; Huybrechts, 2002; Paulson et al., 2005).
Examples
An example run with input parameters, BLD files, as well as a figure / movie of the output
Follow the next steps to include images / movies of simulations:
- Upload file: http://csdms.colorado.edu/wiki/Special:Upload
- Create link to the file on your page: [[Image:<file name>]].
See also: Help:Images or Help:Movies
Developer(s)
References
- Hutton, E. W. H. and Syvitski, J. P. M., 2008. Sedflux 2.0: An advanced process-response model that generates three-dimensional stratigraphy. Computer & Geosciences, 34: 1319~1337, Doi: [10.1016/j.cageo.2008.02.013]